How to setup edimax n300
![how to setup edimax n300 how to setup edimax n300](https://i.ebayimg.com/images/g/viQAAOSwra1fkFbW/s-l300.jpg)
Make sure you have one next to the Security Key. When it it completed, you should have one(1) or (2) green check mark ( ) depending on running firmware.
#How to setup edimax n300 password
It is trying to verify the input password from the main router and make a connection. It should be doing a 2.4GHz Connection Test now.Extender cannot use a different password but the same one as the main router. You can change to any name you want but try not to use the same one from the main router.įor the Wi-Fi Network Password, please input the exact same password from the main router. By default, we add _2EX at the end of your main Wi-Fi Network Name. Please select User Defined for the Wi-Fi Network Name. You're at the Change Basic Setting page now.On the iQ Setup page, select your WiFi network from the table by clicking the little circle in the front and make sure the Signal Strength is at least 40%.Simply read through it and then click the Next button to continue.
![how to setup edimax n300 how to setup edimax n300](https://www.edimax.com/edimax/mw/cufiles/images/products/pics/ew-7438rpn_mini/features/EW-7438RPn_3-in-1_mode-01.png)
On the Recommended Location page, it just tells you where to locate the Extender.On the Change Mode page, select the operating mode - Wi-Fi Extender, Wi-Fi Bridge, or WiFi Access Point - by clicking the picture on the left.Click the Get Started button near the bottom to start the setup process.
#How to setup edimax n300 mac
![how to setup edimax n300 how to setup edimax n300](https://c1.neweggimages.com/ProductImageCompressAll1280/33-315-167_R04.jpg)
At the URL Address bar (not Search bar), type in "" without the quotes.From your computer, search for a WiFi network named "Edimax.Setup **" without the quotes where ** are the last two(2) hexadecimal numbers of your unit's MAC address.Once finished, make use you revert the TCP/IPv4 back to original settings otherwise, you won't be able to access the Internet.Follow the onscreen instructions to finish the setup.If everything is right, you should be at the iQ Setup page to start your setup process.click OK button again to have the new settings to take effect after that, click OK button to save and close the TCP/IP Properties window from TCP/IP Properties window, select Use the following IP address from Properties window, highlight Internet Protocol Version 4 (TCP/IP) from the shortcut menu, select Properties from Network Connections window, right click on Local Area Connection on the left, select Change adapter settings go to Control Panel > Network and Internet > Network and Sharing Center If you have problem accessing the above address, you may want to try these (Windows platform only.).If your computer also has a wireless connection, temporary disconnect or disable it.Connect your computer to the extender's RJ-45 jack using an Ethernet cable.Follow the onscreen instructions to finish the setup.If everything is right, you should be at the iQ Setup page to start the setup process.When prompts for Username and Password, use "admin" and "1234" without the quotes respectively.At the URL Address bar (not Search bar), type in " ******" or "" without the quotes.Then, open a browser (Internet Explorer, Firefox, Chrome, or Safari.).Once found, connect to it (it is an open network, i.e.From your computer, search a WiFi network named "extender ******" without the quotes where ****** are the last six(6) hexadecimal numbers of your unit's MAC address.If you have something else, remove it from the power and then wait for about 15 seconds before plugging it back then, repeat the above steps again when finished, you should only see the following LEDs for v1~v3 and a solid red LED for Air.after that, release it and wait for about 30~45 seconds for it to finish booting up again.while it is powered ON, press and hold down the WPS button for at least 20 seconds.plug the unit into the power outlet and wait for about 30~45 seconds for it to finish booting up.That means you have to re-do the setup one more time. Please note that resetting the unit back to factory defaults will erase all the existing settings in it. If you could not find that wordings, most likely you have the EW-7438RPn Air. From there, you will see the wordings MADE IN CHINA and right next to it is the revision number.
#How to setup edimax n300 how to
Here's how to identify the Hardware Revision. There are four(4) different hardware revisions for EW-7438RPn N300 WiFi Extender.